TB6600 4A Single Axis MicroStepping Stepper Motor Driver Controller
TB6600 4A Single Axis MicroStepping Stepper Motor Driver Controller
Description
TB6600 is 2nd generation PWM chopper-type single-chip bipolar sinusoidal micro-step stepping motor driver. This 4A drive is better than HY-268N-DIV-5A stepper drive. This 2-phase bipolar-type stepping motor can be driven by only clock signal with low vibration and high efficiency and low heat generation. Suitable for drive Two-phase stepping motor dynamic voltage 9V to 40V, the maximum drive current is less than 4A.
This drive uses the current loop subdivision control, the motor torque ripple is very small, low-speed running is very smooth. High-speed torque is much higher than other two-phase drives, high positioning accuracy. Widely used in the engraving machines, CNC machine tools, packaging machinery and other high resolution requirements on the device. NEMA17, NEMA23, NEMA24 and NEMA34 stepper motors work perfectly with this 4A Stepper Driver.
Features
- PWM constant current drive single-chip bipolar sinusoidal micro-step stepping motor driver
- Selectable excitation mode (1/1, 1/2, 1/4, 1/8, and 1/16 step)
- Single power supply
- Average current control (in 8 steps from 0.5A to 3.5A), two-phase sinusoidal current drive output
- DC 9 ~ 40V Single power supply operation
- Optically isolated inputs
- Over voltage, under-voltage, over-current, and short-circuit protection
- High starting speed
- High-speed torque
- Black Rugged All metalic Enclosure and Large Black Aluminium Heat Sink
- Mounting Holes on Heat Sink for Mounting the Drive in Machine Panels
Technical Specifications
- Input voltage DC 8 ~ 50V input (Operating Voltage: 9V – 40V)
- The input current of 1 to 4 amps
- Output current:
- IOUT= 4.0 A (absolute maximum ratings, peak, within 100ms)
- IOUT= 3.5 A (operating range, maximal value)
- Operating Temperature: -10 to 45 ℃
- Storage temperature: -40 ℃ to 70 ℃
- Weight 200 grams
Pinouts
PIN # | PIN NAME | DESCRIPTION |
1 | ENA- (ENA) | Direction Input Cathode of Optoisolator |
2 | ENA+(+5V) | Direction Input Anode of Optoisolator |
3 | DIR- (DIR) | Pulse Input Cathode of Optoisolator |
4 | DIR+(+5V) | Pulse Input Anode of Optoisolator |
5 | PUL- (PUL) | Enable Input Cathode of Optoisolator |
6 | PUL+ (+5v) | Enable Input Anode of Optoisolator |
7 | B- | Stepper Motor Output Winding B Negative |
8 | B+ | Stepper Motor Output Winding B Positive |
9 | A- | Stepper Motor Output Winding A Negative |
10 | A+ | Stepper Motor Output Winding A Positive |
11 | GND | Power Supply Input Negative / 0V |
12 | VCC | Power Supply Input Positive /9V to +40V (Operating Voltage) |
Documents and Downloads
- Example with code
- GRBL Free CNC controller software for Arduino
- User Guide
Notes:
- This motor driver may not be suitable for high holding (static) torque requirements. This is because this drive uses builtin decay mode circuit to force static holding current to become low. This prevents over heating of the stepper motors.
- If Stepper motor vibrates but does not turn in any direction make sure that your motor connections for Windings A and B are not exchanged.
- If Stepper motor does not runs or locks at all make sure the Enable Signal polarity is correct.
- If Stepper motor does not runs or locks at all make sure that the power to the Drive is correct
- If Stepper motor does not runs or locks at all make sure the 3x SUB Switches are not all set to ON or all set to OFF
Package Includes
- 1x 4A TB67S109AFTG 4A Single Axis MicroStepping Stepper Motor Driver Controller